Faber INCA PRO 30 RB User Manual download pdf

READ AND SAVE THESE INSTRUCTIONS.

The Installer must leave these instructions with the homeowner.

The homeowner must keep these instructions for future reference and for local electrical inspectors’ use.

WARNING

Risk of electrical shock. Electrical wiring must be done by qualiÞ ed personnel in accordance with all applicable codes and standards. Turn

off the power and lock out the service panel before installing, wiring, or servicing this product. To prevent serious injury from electrical

shock or damage to electrical components - MAKE SURE POWER IS OFF! This unit must be grounded.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Installation Work And Electrical Wiring Must Be Done By QualiÞ ed Person(s) In accordance With All Applicable Codes and Standards,

Including Fire-Rated Construction.

b. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden wires.

MAKE YOUR CUT-OUTS.

WARNING

• Cut a level 4 11/32” X 3 5/32” hole in to your desired location.

• Route the electrical cable from the hood to the wall control location.

INSTALL THE REMOTE WALL CONTROL

WARNING – To reduce the risk of Þ re and electric shock, do not use this

control in an insulated wall

• Remove the back metalic panel of the Remote Wall Control by removing the four

screws.

• Insert and Þ x a cable with four wires (Brown, Black, Red and Green Ground Wire)

into the knockout hole of the back metalic panel.

• Connect the green ground wire from the cable to the green ground screw.

• Connect the red wire from the cable to the red Remote Wall Control wire with a

twist-on wire connector.

• Connect the brown wire from the cable to the white/black Remote Wall Control

wire with a twist-on wire connector.

• Connect the black wire from the cable to the two black Remote Wall Control wires

with a twist-on wire connector.

• Replace the back metalic panel.

The twist on wire connector should be suitable for connecting multiple wires of different sizes

together.

• Remove the faceplate from the Remote Wall Control by removing two screws.

• Position the remote control box in a hole so that both face plate mounting tabs are ß ush to the

Þ nished wall surface. Fasten it to a wall stud using four screws (not supplied)

• Reinstall the control faceplate, ensuring not to pinch the wires.

CONNECTION OF THE REMOTE WALL CONTROL TO THE RANGEHOOD

To install the rangehood, please refer to the hood installation instructions.

• Remove the grease Þ lters USING TWO HANDS one to hold the Þ lter so that it doesn’t fall on

cooktop and one to turn the knob by pulling the knob out and turning to the left.

• Remove the entire bottom of the rangehood by pushing your thumbs into the side holes and

pulling the sides free from the rangehood.

REMOTE WALL CONTROL INSTALLATION INSTRUCTIONS

WARNING – To reduce the risk of Þ re, electric shock and injury to persons, the Remote Wall Control must be

installed only with Faber range hood models INCA PRO 30 RB or INCA PRO 38 RB, that are marked to indicate

suitability with this product. Other models cannot be used

black wiring

Y/G wiring

red wiring

white wiring

brown wiring

1 2

WARNING 1
WIRING DIAGRAM 2

Summary of Contents

Page 1 - WARNING

READ AND SAVE THESE INSTRUCTIONS. The Installer must leave these instructions with the homeowner.The homeowner must keep these instructions for future

Page 2 - WIRING DIAGRAM

• Remove the wiring box cover by removing the two screws.• Disconnect the two red wires by removing the twist-on wire connector.• Remove the Intern

Comments to this Manuals

No comments

Faber INCA PRO 30 RB User Manual

Browse online or download User Manual for Unknown Faber INCA PRO 30 RB. Faber INCA PRO 30 RB User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Faber INCA PRO 30 RB