Faber Agio User Manual download pdf (Page 7)

Version 10/05 - Page 7

Three Screws

Rangehood Body

Front

Strip

CUSTOMIZING YOUR RANGEHOOD

The front strip of the rangehood can be customized by replac-

ing the factory supplied strip with a custom front strip made

from the same materials as your cabinets. The front strip is

attached to the rangehood by three recessed screws and

three key hole slots on the back side of the strip as indicated

in FIGURE 15. It is necessary only to remove the three lower

screws to remove the front strip. The top screws will slide out

of the key holes once the three lower screws are removed.

Side View of the Rangehood

The front strip dimensions are given in FIGURE 16. For a

custom front strip, a local cabinet shop can make a strip to

match your cabinets. If you wish to keep the frame of the front

panel and only replace the glass panel, the dimensions follow:

Height = 5 11/16", Depth = 1/8", Width = 29 11/16" (for 30"

model) 35 11/16" (for 36" model) 23 5/8" (for 24" model).

WARRANTY & SERVICE

All Faber products are warranteed against any defect in materials or

workmanship for the original purchaser for a period of 1 year from the

date of original purchase. This warranty covers labor and replace-

ment parts. The warranty does not cover consumable parts such as

ﬁlters and light bulbs. This warranty does not apply if this product

has been subjected to faulty installation, misuse, or neglect. This

warranty excludes any consequential expense or damage resulting

from any use or malfunction of the product. All implied warranties

are limited to the duration of this warranty.

To obtain warranty service, contact the dealer from whom you pur-

chased the rangehood, or the local Faber distributor. If you cannot

identify a local Faber distributor, contact us at (508) 358-5353 for

the name of a distributor in your area.

FIGURE 16

WIRING DIAGRAM

• This rangehood uses Flourescent Lamp Type F33-15W-T8 and

Starter Type S2.

Rangehood Control Panel

All controls are located under the front panel and are shown in

FIGURE 17.

Light On/Off Switch ( L )

On/Off switch for the ﬂuorescent light. Moving the switch to the

1 Position turns the light On. Moving the switch to the 0 Position

turns the light Off.

FIGURE 15

FIGURE 17

FIGURE 18

Blower Speed Switch ( S )

Controls blower speed. Moving the switch to the 1 Position turns

the blower on LOW. Moving the switch to the 2 Position turns the

blower on MEDIUM. Moving the switch to the 3 Position turns the

blower on HIGH.

Operation Indicator Light ( I )

Red light will be on when the rangehood is operating.

Microswitch ( MS )

When the front panel of the rangehood is closed, the rangehood

will turn off by a microswitch. This turns the rangehood On and

Off without adjusting the switches for the Light or Blower and it

remembers the last speed setting.

Cleaning

The metal grease ﬁlters should be cleaned frequently in hot deter-

gent solution or placed in the dishwasher. Clean exterior surfaces

with hot soapy water. Using abrasives and scouring agents can

scratch rangehood ﬁnishes and should not be used to clean ﬁnished

surfaces.

Replacing the Fluorescent Light

To replace the ﬂuorescent light, remove the retainer clips from both

ends of the glass diffuser as indicated in FIGURE 18. Carefully

slide the glass diffuser all the way to the left. Lower the right end

of the glass below the support ﬂange, then remove the glass by

sliding it back to the left. Replace the diffuser glass by reversing

these directions.

23 5/8" or 29 15/16" or 35 15/16"

5 7/8"

13/16"

USE AND CARE INFORMATION

This rangehood system is designed to remove smoke, cooking

vapors and odors from the cooktop area.

For Best Results

Start the rangehood several minutes before cooking to develop proper

airﬂow. Allow the unit to operate for several minutes after cooking

is complete to clear all smoke and odors from the kitchen.

Blower On/Off

Switch ( M )

On/Off switch for the

blower. Moving the

switch to the 1 Posi-

tion turns the blower

On. Moving the switch

to the 0 Position turns

the blower Off.

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Faber Agio User Manual Page 7

Comments to this Manuals

Related products and manuals for Cooker hoods Faber Agio